임의 함수 발생기 (TOE 7761 - Discontinued)
- 상세 설명
TOE 7761 임의 함수 발생기는 DDS(직접 디지털 합성) 기술을 사용하여 고품질 및 정확도의 사인파를 생성합니다. 사각 파형은 빠른 상승 및 하강 시간으로 제공됩니다. 최대 80MS/s의 샘플링 속도는 외부 클록으로 제어할 수 있습니다.
임의 신호는 14비트 분해능으로 최대 1.000.000개의 샘플링 포인트를 가질 수 있으므로 자연 신호를 매우 잘 시뮬레이션할 수 있습니다. 사인, 삼각, 사각, 램프 등과 같은 광범위한 통합 표준 파형은 새로운 임의 파형 생성을 단순화합니다.
출력 진폭은 최대 ±10V(50Ω에서 ±5V)의 오프셋과 함께 최대 20Vpp(10Vpp에서 50Ω)로 설정할 수 있습니다. 내부 또는 외부 트리거 소스가 있는 다양한 트리거 모드를 통해 정확한 수의 사용자 정의 주기를 생성할 수 있습니다. 다양한 변조 및 스위프 옵션이 장비 기능을 마무리합니다.
10MHz 외부 클럭 레퍼런스를 통해 정확한 위상 조정을 위해 장치를 동기화할 수 있습니다.
그래픽 LCD와 다기능 스핀휠로 조작이 쉽고 편리합니다. 몇 가지 입력만으로 모든 기능을 구성할 수 있습니다. 또한 비휘발성 메모리에 최대 50개의 기기 구성을 저장할 수 있습니다.
Special features
- 1μHz ~ 40MHz 사인 및 구형파
- 최대 20Vss의 출력 진폭
- 14비트 분해능 및 최대 1,000,000샘플링 포인트의 임의 파형의 80MS/s 샘플링 속도
- 1 000 000 샘플링 포인트용 플래시 메모리
- 많은 표준 파형이 임의 파형 생성을 지원합니다.
- 다양한 변조 및 스위프 옵션
- 50개의 기기 구성을 저장할 수 있습니다.
- USB-1), GPIB 및 RS-232 인터페이스를 통한 원격 제어
1) RS232 어댑터를 통한 USB 제공
임의 파형 기능
포함된 PC 소프트웨어를 사용하면 복잡한 파형을 쉽게 생성, 편집 및 다운로드할 수 있습니다. 실행 준비가 된 기기의 플래시 메모리에 여러 파형을 저장할 수 있습니다.
Arbitrary characteristics
Resolution | |
horizontal | Up to 1,000,000 points |
Vertical | 14 bits (- 8191 to + 8191) |
Sampling | 12.5 ns/point to 100 s/point (80 MS/s max.) with 4 digits or 0.1 ns resolution |
Accuracy | 0.002 % (20 ppm) |
Predefined waveforms | Sine, triangle, square, noise, ramp up and down, Sin(x)/x, exponential rise and fall, Gaussian pulse |
Technical Data
Frequency characteristics
Sine | 1 μHz to 40 MHz |
Square | 1 μHz to 40 MHz |
riangle | 1 μHz bis 5 MHz |
Pulse | 0,5 mHz to 10 MHz |
Accuracy | 0.002 % (20 ppm) |
Resolution | 12 digits oder 1 μHz |
Waveform characteristics
Sine Harmonic distortion Signal distortion (non-harmonic) | DC to 20 kHz -65 dBc 20 kHz bis 100 kHz -60 dBc 100 kHz bis 5 MHz -45 dBc 5 MHz bis 40 MHz -30 dBc DC to 1 MHz < -60 dBc |
Triangle Variable symmetry | 10 % to 90 % |
Square Transition times Duty cycle < 10 MHz < 30 MHz < 40 MHz Symmetry error Overshoots | < 8 ns at full amplitude into 50 Ω 20 % to 80 %, ±1 % max. 40 % to 60 %, ±5 % max. 50 % fixed < 1 % at 50 % duty cycle Typ. < 3% of output amplitude ± 50 mV |
Pulse Pulse width Overshoots | > 50 ns or 0.0001 % of repetition rate Typ. < 3 % of output amplitude ± 50 mV |
Output characteristics
Amplitude Range Resolution Units Accuracy Linearity | 20 mVpp to 20 Vpp max., 10 mVpp bis 10 Vpp an 50 Ω 3 digits or 10 mV Vpp, Vrms, dBm ±2 % ±10 mV of the set value at 1 V tos 10 V 0.1 dB to 1 MHz, 1.5 dB to 40 MHz |
Offset Range Resolution Accuracy | Up to ±9.99 V max., up to ±4.99 V into 50 Ω, depending on the set amplitude 3 digits or 10 mV ±2% ±10 mV into 50 Ω |
Main output | 50 Ω 9th order elliptic filter and 5th order Bessel filter Short-circuit proof and resistant to external voltage up to ±15 V. The output is automatically disconnected in event of overload. |
Operating modes Continuous Trigger Gate Burst | Continuous output signal with the set parameters Output retains last value of last waveform until a trigger event arrives, and exactly one complete waveform is subsequently output with the programmed parameters Like trigger mode except that the output signal is generated for the duration of the gate signal. The last started cycle is completed. Like trigger mode except with a programmed number of 2 to 999 999 cycles. |
Trigger characteristics Source Start phase Repetition rate internal external Pulse width | Internal, external, manual or remote-controlled interface -360° to + 360° with 0.1 ° resolution 0.01 Hz to 1 MHz, accuracy ± 0.002 % < 10 MHz (DDS-Signal), < 20 MHz (arbitrary) > 20 ns, (TTL) |
Modulation characteristics
Amplitude modulation Internal External | 0.01 Hz to 20 kHz sine, square or triangle, variable modulation from 0 % bis 100 % 5 VPP for 100 % modulation |
Frequency modulation Internal External | |
FSK Clock rate Internal External1) | 0.01 Hz to 1 MHz TTL-Signal, max. 1 MHz |
1) External FSK modulation uses Trigger In. Specifications subject to change without notice
Sweep characteristics
Characteristic Sweep time Trigger | Linear up, down, up and down Logarithmic up or down 10 ms to 500 s Internal or external, all trigger modes |
Inputs and outputs
Summing In Modulation In | The analog input signal can be added to the output signal. 5 Vpp for full-scale output, bandwidth: DC to > 10 MHz, impedance 500 Ω 5 Vpp für 100 % modulation, bandwidth: DC to > 50 kHz, Impedance 10 kΩ |
Trigger In Reference In Reference Out Marker Out Sync Out | TTL compatible, max. 20 MHz, pulse width > 20 ns, impedance 10 kΩ 10-MHz square signal for device synchronization, TTL compatible, input impedance 1 kΩ 10-MHz square signal or arbitrary clock for device synchronization, TTL compatible, impedance 50 Ω Positive TTL pulse as marker for arbitrary signals, freely-programmable, impedance 50 Ω Positive TTL pulses synchronous with the output frequency, impedance 50 Ω |
Configuration memory | 50 instrument settings, including last setting |
Arbitrary memory | 1,000,000 points in internal flash memory |
Remote-controlled interfaces | IEEE 488.2 (GPIB), RS 232 (115 kB max.), USB1),SCPI compatible |